Electrical Engineering Archives - Page 2 of 2

Sign Up

Sign Up to our questions and Answers Engine to ask questions, answer people’s questions, and connect with other people.
👉Note: After Sign Up. A confirmation mail will be sent to your registered email account, If you have not received the confirmation mail, kindly Check Your Spam Mails.

Sign In

Forgot Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email. If not received mail yet, please check your spam mails.

Username* Please type your username.

E-Mail* Please type your E-Mail.

Question Title*

Please choose an appropriate title for the question so it can be answered easily.

Category* Please choose the appropriate section so the question can be searched easily.

Tags Please choose suitable Keywords Ex: question, poll.

Is this question is a poll? If you want to be doing a poll click here.

Image poll?

Featured image

Browse

Details*

Type the description thoroughly and in details.

Add a Video to describe the problem better.

Video type Choose from here the video type.

Video ID Put Video ID here: https://www.youtube.com/watch?v=sdUUx5FdySs Ex: "sdUUx5FdySs".

Ask Anonymously

Get notified by email when someone answers this question.

By asking your question, you agree to the Terms of Service and Privacy Policy .*

Please briefly explain why you feel this question should be reported.

Please briefly explain why you feel this answer should be reported.

Please briefly explain why you feel this user should be reported.

Ask A Question

VishalProfessional

Asked: 2 months agoIn: Electrical Engineering

A second order pressure transducer has a natural frequency of 1000 rad/sec and damping ratio of 0.29. Its static sensitivity is 0.02 V/bar. Using Fourier transforms method; plot the frequency response of the input signal and the output voltage.

A second order pressure transducer has a natural frequency of 1000 rad/sec and damping ratio of 0.29. Its static sensitivity is 0.02 V/bar. Using Fourier transforms method; plot the frequency response of the input signal and the output ...Read more

VishalProfessional

Asked: 2 months agoIn: Electrical Engineering

In the measurement of surface roughness, height of 16 successive peaks and troughs were measured from a datum and were: 25, 43, 23, 33, 19, 40, 37, 26, 35, 22, 38, 27, 36, 25, 41 and 21 µm. If these measurements were obtained over a length of 16 mm, determine: a)The C.L.A. (i.c. Ra), R.M.S and Rz values of the rough surface. b)Determine the grade of roughness in case of Ra value.

In the measurement of surface roughness, height of 16 successive peaks and troughs were measured from a datum and were: 25, 43, 23, 33, 19, 40, 37, 26, 35, 22, 38, 27, 36, 25, 41 and 21 µm. ...Read more

VishalProfessional

Asked: 2 months agoIn: Electrical Engineering

In the measurement of surface roughness, height of 18 successive peaks and troughs were measured from a datum and were: 35, 22, 38, 26, 35, 18, 43, 28, 32, 21, 39, 26, 41, 22, 29, 18, 36 and 16 um. If these measurements were obtained over a length of 18 mm, determine a) The C.L.A. (i.e. Ra), R.M.S and Rz values of the rough surface. b) What is the grade of roughness corresponding to the evaluated value of Ra?

In the measurement of surface roughness, height of 18 successive peaks and troughs were measured from a datum and were: 35, 22, 38, 26, 35, 18, 43, 28, 32, 21, 39, 26, 41, 22, 29, 18, 36 and ...Read more

Anonymous

Asked: 2 months agoIn: Electrical Engineering

A single strain gauge having resistance of 150 Ω is mounted on a steel cantilever beam at a distance of 0.2m from the free end. The beam dimensions are 30 cm (length) x 1.8 cm (width) x 0.28 cm (depth). An unknown force F applied at the free end produces a deflection of 11 mm at the free end. If the change in gauge resistance is found to be 0.1522. Calculate the gauge factor. Take Young's modulus of steel as 200 GN/m²

A single strain gauge having resistance of 150 Ω is mounted on a steel cantilever beam at a distance of 0.2m from the free end. The beam dimensions are 30 cm (length) x 1.8 cm (width) x 0.28 ...Read more

VishalProfessional

Asked: 2 months agoIn: Electrical Engineering

In the measurement of surface roughness, height of 20 successive peaks and troughs were measured from a datum and were: 33, 25, 40, 22, 35, 18, 42, 25, 35, 22, 36, 18, 42, 22, 31, 21, 36, 18, 35 and 20 μm. If these measurements were obtained over a length of 20 mm, determine the C.L.A. (i.e. R a ), R.M.S and R z values of the rough surface. B) Determine the grade of roughness in case of R a value.

In the measurement of surface roughness, height of 20 successive peaks and troughs were measured from a datum and were: 33, 25, 40, 22, 35, 18, 42, 25, 35, 22, 36, 18, 42, 22, 31, 21, 36, 18, ...Read more

Anonymous

Asked: 2 months agoIn: Electrical Engineering

In measurement of surface roughness, heights of 10 successive peaks and troughs were measured from a datum were 35, 25, 40, 22, 35, 18, 42, 25, 35, 23 microns. Determine i) Rt ii) Ra iii) average over definite ordinates iv) Root mean square value of roughness v) International grade of roughness.

In measurement of surface roughness, heights of 10 successive peaks and troughs were measured from a datum were 35, 25, 40, 22, 35, 18, 42, 25, 35, 23 microns. Determine i) Rt ii) Ra iii) average over definite ...Read more